Beijing Golden Eagle · Since 2003

LED UV Exposure Machine GE-LED1400 — Single-Side Vacuum

Single-side LED UV exposure machine with an 1800×1400 mm glass table and vacuum frame. Taiwan LED chip, 1 kW total power on a single 220 V supply, 0–999 s exposure timer. For PCB and FPC dry- and wet-film imaging, screen plate making, and metal etching exposure.

CE Certified 24h Quotation 1-Year Warranty Worldwide Delivery
GE-LED1400 single-side LED UV exposure machine with vacuum frame

LED UV Exposure Machine GE-LED1400

GE-LED1400 single-side LED UV exposure machine
GE-LED1400 single-side LED UV exposure machine — 1800×1400 mm glass table, vacuum frame, Taiwan LED chip light source.

What Is the GE-LED1400 LED UV Exposure Machine?

The GE-LED1400 is a single-side vacuum exposure machine that uses a UV LED array instead of a traditional UV lamp. Artwork film is laid on the 1800×1400 mm glass table, the coated panel or screen is placed on top, the rubber blanket is lowered and locked, and the vacuum pump pulls film and substrate into hard contact before the LED array fires for a set time.

It is used for PCB circuit board manufacturing, FPC dry- and wet-film imaging, screen plate making, and metal etching exposure — anywhere a pattern has to be transferred into photoresist on one side of a flat panel.

Beijing Golden Eagle builds the GE-LED1400 in Beijing. Shipped in a wooden case with a 12-month warranty; free technical training at our Beijing factory, or on-site training in your country on request.

How It Works

  1. Clean the table — wipe the glass table and the blanket with alcohol; no hard objects on the glass.
  2. Lay the film — position the artwork film on the glass table.
  3. Place the work — set the thoroughly dried, photoresist-coated panel or screen on the film, with the suction pipe at the side of the frame.
  4. Close and lock — lower the rubber blanket cover and fasten the latch.
  5. Set the vacuum time — press the suction button and set the draw-down time, normally 20–30 seconds.
  6. Set the exposure time — press the exposure button and set the time on the three-digit display, range 0–999 seconds. For screen plate making 60–120 seconds is the usual starting point.
  7. Confirm and start — press reset to confirm the settings, then start. The machine draws vacuum and exposes for the set time, then switches the lamp and vacuum off automatically.

Technical Specifications

ParameterSpecificationNotes
ModelGE-LED1400Quoted as GE-1800 on our quotation sheet
Light sourceTaiwan LED chipUV LED array, no preheat
Glass table1800 × 1400 mmSingle-side exposure area
Total power1 kWLow consumption for the table size
Power supply220 V / 50 Hz or 60 HzSingle phase
Machine dimensions1800 × 1500 × 1050 mmL × W × H
Vacuum systemVacuum pump, rubber blanket with latchDraw-down 20–30 s typical
Exposure timer0–999 s, three-digit display60–120 s typical for screen plate making
ControlComputer screen control systemSuction time, exposure time, reset, start
LED service life20,000–30,000 hoursFrequent switching does not shorten it
ApplicationsPCB, FPC dry and wet film, screen plate making, metal etchingSingle-side flat work
PackingWooden case 
Warranty12 monthsMain parts and spares for wear items
Lead timeAbout 10 daysFrom receipt of deposit

Source: Golden Eagle exposure equipment quotation and the GE-1800 instruction sheet. Ask us for the current price — FOB Xingang or EXW Beijing.

Why a UV LED Light Source?

  • No warm-up — the LED array is at full output the moment it is switched on, so there is no idle lamp burning between jobs.
  • Low heat into the glass — a traditional UV lamp heats the table, and repeated plate making then distorts the image because the screen mesh moves. LED runs cool, so repeat plates stay dimensionally true.
  • Stable, even output — a single LED light source with strong effective wavelength gives higher fidelity than a traditional UV lamp: smoother screen lines and finer halftone dots.
  • 20,000–30,000 hour life — no frequent tube changes, and switching it on and off does not shorten it. Consumable cost drops accordingly.
  • 1 kW for an 1800×1400 mm table — the whole machine runs off a single 220 V supply.

Where It Fits in the Line

Exposure sits between coating and developing. A typical route is resist coating or dry film lamination → drying → GE-LED1400 exposure → developing → etching → stripping.

For double-sided PCB work where both faces must register to each other, see the double-sided exposure machine or the 8-CCD solder mask double-sided exposure machine. For the full exposure range and the five table formats we build, see PCB exposure machines.

Frequently Asked Questions

Is GE-LED1400 the same machine as GE-1800?

Yes. GE-LED1400 is the model designation we use; older exposure equipment quotations list the same machine as GE-1800. Both are the single-side LED UV exposure machine with an 1800×1400 mm glass table.

What exposure time should I set?

The timer runs 0–999 seconds on a three-digit display. For screen plate making, 60–120 seconds is the usual range, adjusted for what you are holding — text, fine line, halftone dot or solid. Vacuum draw-down is set separately, normally 20–30 seconds. Dry film and liquid resist need their own times depending on the resist and its thickness.

Can it expose metal sheet, not just PCB?

Yes. The GE-LED1400 is used for metal etching exposure as well as PCB and FPC imaging — nameplates, signage, cutting dies, filter mesh and decorative panels, as long as the work is flat and exposed on one side.

Does it do double-sided exposure?

No. The GE-LED1400 is a single-side machine. For double-sided boards that need top and bottom artwork registered to each other, use the double-sided exposure machine or a CCD-aligned model.

How do I look after the glass table and blanket?

Clean both with alcohol only. Do not scratch the glass or the blanket with hard objects, and do not knock either with anything heavy. Never look directly at the UV LED lamp while it is working.

What is the warranty and lead time?

12-month warranty covering main parts and spare accessories for wear items; after the first year, spares are supplied at basic cost. Lead time is about 10 days from receipt of the deposit. Technical training is free at our Beijing factory, and we can travel for installation and training on request.